The installation of a Sublimistick protection kit requires calm and thoroughness. If you are not sure of your skills, we invite you to contact your nearest Slicy dealer for a perfect set-up. Find our dealers HERE

Preparation :

– Make sure you are in a clean and warm, indoor space (17°C to 27°C).
– Clean and degrease your bike paying close attention to every little detail.
– Remove inconvenient components or old decals to facilitate the installation.
– Ensure the bike has been allowed to dry for some hours.
– Fill the spray bottle with our install shampoo. Add 0.5ml for 0.5L of warm water.
– Thoroughly wash your hands.

Installation :

– Identify Sublimistick sections using the bike diagram.
– Spray water to your fingers.
– Peel the section of Sublimistick off and spray water immediately on the sticky side.
– Spray water on the frame’s location.
– Apply the wet Sublimistick section to the frame. Center and line up the piece according to the diagram.
– Repositionining is possible if the Sublimistick section is still wet.
To move, peel back, add further water to the frame and Sublimistick section then re-apply in correct location.
– Use the Slicy squeegee to remove water and air. Start at the centre of the Sublimistick section and pull the water and air to the outside.
– Use a microfiber to collect any excess water.
– Wait few minutes and use your fingers to check if all edges are firmly pressed down.
– For a perfect finish, use the hair dryer to dry the Sublimistick sections. Do not overheat.
– Repeat these steps for each section of Sublimistick.
– Kits are designed with a 1 mm gap between Sublimistick sections.
– Let your bike dry in a warm workspace for 24h.
– Do not ride or wash your bike for 24h.

Removal :

– Use a hair dryer to heat the adhesive.
– Peel back a corner and remove remove the section very slowly.

Disclaimers :

– Slicy is not responisble for any damage caused to your bike during installation or removal of the Sublimistick Integral Kit.
– If you have any problems or issues with your Sublimistick Integral Kit, please contact a member of our team at: contact@slicy-products.com.

The installation of a Sublimistick Fork protection requires calm and thoroughness. If you are not sure of your skills, we invite you to contact your nearest Slicy dealer for a perfect set-up.

Preparation :

– Make sure you are in a clean and warm, indoor space (17°C to 27°C).
– Clean and degrease your fork paying close attention to every little detail.
– Remove inconvenient components or old decals to facilitate the installation.
– Ensure the bike has been allowed to dry for some hours.
– Fill the spray bottle with our install shampoo. Add 0.5ml for 0.5L of warm water.
– Thoroughly wash your hands.

Installation :

– Identify Sublimistick sections using the bike diagram.
– Spray water to your fingers.
– Peel the section of Sublimistick off and spray water immediately on the sticky side.
– Spray water on the frame’s location.
– Apply the wet Sublimistick section to the fork. Center and line up the piece according to the diagram.
– Repositionining is possible if the Sublimistick section is still wet.
To move, peel back, add further water to the fork and Sublimistick section then re-apply in correct location.
– Use the Slicy squeegee to remove water and air. Start at the centre of the Sublimistick section and pull the water and air to the outside.
– Use a microfiber to collect any excess water.
– Wait few minutes and use your fingers to check if all edges are firmly pressed down.
– For a perfect finish, use the hair dryer to dry the Sublimistick sections. Do not overheat.
– Repeat these steps for each section of Sublimistick.
– Let your bike dry in a warm workspace for 24h.
– Do not ride or wash your bike for 24h.

Removal :

– Use a hair dryer to heat the adhesive.
– Peel back a corner and remove remove the section very slowly.

Disclaimers :

– Slicy is not responsible for any damage caused to your bike during installation or removal of the Sublimistick kit.
– If you have any problems or issues with your Sublimistick Fork Kit, please contact a member of our team at: contact@slicy-products.com.